Skip to content
Menu
Heavy Operations Applications

Motor Start

Purpose-built to handle frequent motor starts and extended lifecycles for long-duration loads without performance degradation.

NanoPlex™ HDC in Motor Starts

NanoPlex™ HDC brings film durability to single-phase start capacitors and capacitor discharge ignition (CDI). Electric motors need high starting torque and starts come often, to run dependably and in hot enclosures.

Example Applications:

  • HVAC and refrigeration: hard-start kits for air conditioner and heat pump compressors, commercial refrigeration compressors, walk-in coolers and freezers
  • Jet engine ignition: Capacitor discharge ignition (CDI) is the primary ignition means in jet engines. These require high thermal stability and energy density which HDC enables.
  • Water and wells: three-wire submersible well pumps, jet pumps, single-phase irrigation pumps all rely start capacitors, often operating in environments which harm lifetime and lead to repairs.
  • Agriculture: grain and feed augers, conveyors, farm-duty motors, barn and poultry equipment, milk and vacuum pumps as require start capacitors
  • Shop and light industrial: air compressors, woodworking and metalworking machinery, pressure washers, mixers, conveyors
  • Pool and pumps: single-speed pool and spa pumps
  • Electrolytics hold most start positions due to their high capacitance, but multiple lifetime concerns including sudden failure, thermal instability, and self-heating mean they are a major limitation.
  • NanoPlex HDC packs more capacitance into film, making film start capacitors practical where they used to be too bulky.
  • Designers gain film durability in hard-start kits and motor-mounted capacitors.
  • Electrolytic start capacitors have dissipation factors that limits them to short, infrequent starts, about twenty 3-second starts an hour. Starting any more frequently, especially in an already hot environment, easily pushes the part past its 65C rating and lead to electrolyte vaporization, a massive loss of capacitance and a steep rise in ESR.
  • HDC’s dissipation factor of 0.5 to 1.0% is 10 to 20X lower, so each start creates less self-heating in the part.
  • Short-cycling compressors, busy well pumps and high-inertia loads like augers and conveyors get a start capacitor built for their high duty cycle.
  • A motor’s starting torque depends on its capacitor holding its value across all ranges. HDC film holds steady at high and low temperatures and under higher electrical loads.
  • Electrolytic start capacitors lose capacitance at high and low temperatures, under repeated cycling, and at high electrical voltages and frequencies.
  • HDC has no liquid electrolyte to dry out, gas or vent, so a film start capacitor keeps its capacitance from the first start onward.
  • Motors start the same way year after year, with fewer stalled starts, fewer burned windings and fewer service calls.
  • A replacement capacitor should work the day it comes off the shelf, even after months in a warehouse or service truck.
  • Aluminum electrolytics degrade in storage as their oxide layer weakens, and long-stored parts can need reforming before use.
  • HDC film parts have no electrolyte or oxide layer to degrade on the shelf.
  • Distributors and contractors stock hard-start kits and replacement start capacitors with confidence, and technicians install parts that perform as rated.
  • A cold motor needs the most torque, just when an electrolytic capacitor delivers the least.
  • In the cold, electrolyte thickens, so an electrolytic’s capacitance drops and its losses rise, weakening starts on pumps, compressors and farm equipment in winter.
  • Film dielectrics like HDC keep stable electrical properties at low temperature, with no electrolyte to thicken.
  • Outdoor and unheated equipment starts reliably through winter, with fewer no-start calls.

NanoPlex™ HDC Film vs. Electrolytic Start Capacitors

Category Aluminum electrolytics NanoPlex™ HDC film
Construction Etched aluminum foil and electrolyte-soaked paper Nanolayered polymer film, no liquid electrolyte
Capacitance per volume Higher; etched foil packs hundreds of µF into a small can 1.7 to 2.1X BOPP film, less than an electrolytic of the same rating
Cost per µF
Lowest Higher; earns its place where reliability, heat or duty matter
Temperature rating 65°C for standard start parts 105°C film rating without derating, 40°C more headroom
Heat per start Power factor up to 10%; each cycle creates hundreds of Watts of heat Dissipation factor of 0.5 to 0.9%, roughly 10 to 20X less loss
Starting duty
Built for short, infrequent starts, about twenty 3-second starts an hour Lower loss per start suits frequent starts and longer starts
Capacitance over life Falls as the electrolyte dries out, weakening the starting torque No electrolyte to dry out, so capacitance holds steady
Effect on the motor As capacitance falls, starts lengthen, windings heat and motors begin to stall Consistent starting torque year after year
End-of-life behavior Bulges, vents or shorts, often with little warning No electrolyte to gas, leak or vent
Voltage strength Set by a thin anodic oxide layer that weakens with heat and age Breakdown strength of 790 to 820 V/µm at 25°C (ASTM D149), in BOPP’s class
Shelf life Oxide layer degrades in storage; long-stored parts may need reforming No electrolyte or oxide layer to degrade on the shelf
Cold-weather starts Electrolyte thickens in the cold, so capacitance drops and losses rise when a cold motor needs the most torque Film dielectrics keep stable properties at low temperature
Supply chain Much of the motor start supply chain runs through Asia 100% U.S.-engineered and manufactured
Best fit Compact, lowest-cost parts for infrequent starts in moderate temperatures Hard-start kits, pump control boxes, high-cycle and long-start motors, and hot enclosures where space allows a film part
nanoplex-logo-white

Ready to evaluate NanoPlex films?

Request a sample kit for in-house qualification, compatibility testing, and grid-level performance validation.

Top 5 FAQs Consumers Ask About Capacitors in Motor Start-Stop Environments

Peak Nano’s NanoPlex HDC film capacitors are ideal for frequent start–stop environments because they are built to handle the high in-rush currents and electrical stress that damage traditional electrolytic capacitors.

HDC uses a patented nanolayer structure that spreads electrical load and reduces internal heating, allowing it to perform reliably even when motors start dozens or hundreds of times per day.

Traditional electrolytic capacitors fail because they overheat, swell, or break down under repeated in-rush currents, especially in hot or enclosed spaces like attics, engine rooms, or compressor housings.

Peak Nano HDC capacitors run cooler and stay stable under constant cycling, eliminating the weak points that cause early failures. They maintain full performance up to 135°C, far beyond what electrolytics can tolerate.

Common signs include:

  • Slow or weak motor starts
  • Humming or buzzing motors
  • Breakers tripping during startup
  • Frequent restarts
  • The motor refusing to start altogether

With Peak Nano HDC, these symptoms are far less common because the nanolayer design reduces heat, prevents drift, and maintains stable energy delivery through repeated cycles.

Yes. Upgrading to a Peak Nano HDC film capacitor significantly improves reliability and extends equipment life.

HDC capacitors:

  • Provide stronger, more consistent starts
  • Reduce strain on the motor
  • Last much longer than electrolytics
  • Lower the risk of unexpected breakdowns
  • Reduce service calls and maintenance costs
Operators often see a 3-5x improvement in lifespan and far fewer sudden failures.

Absolutely. Peak Nano HDC capacitors are specifically engineered for harsh, high-heat environments where conventional capacitors degrade quickly.

HDC is rated up to 135°C, resists swelling, and runs significantly cooler due to its ultra-low internal losses.

This makes HDC ideal for:

  • Attics and rooftop units
  • Pump houses and compressor enclosures
  • Industrial machinery with poor ventilation
  • Engine rooms or hot mechanical spaces
  • Equipment that cycles on and off continuously
In these environments, HDC provides the stability and durability that traditional capacitors simply cannot match.

Long-Duty Cycles

NanoPlex LDF capacitor film offers low dissipation factors, thermal sustainability, and longer lifespans, providing higher performance and reliability for long-term duty cycles.

  • Up to 5x longer life under continuous load
  • Full power at 135°C with no derating
  • 50% less self-heating for cooler, safer operation
  • High stability for power conversions

Reliable Power for Long-Duty Cycles

LDF Film maintains full performance up to 135°C, eliminating the overheating and derating issues that shut down traditional capacitors during continuous, heavy-duty operation.

  • Industrial equipment runs for long periods without cool-down windows, causing internal capacitor heating and forcing traditional capacitors to derate above 85°C, leading to unstable performance and premature failures in thermally constrained environments.
  • LDF maintains full performance up to 135°C with no derating, in high-heat, long-duration operations, giving systems more thermal headroom and eliminating the overheating and drift that occur during continuous run times or extreme duty cycles.
  • With stable performance at higher temperatures and greater tolerance for long, heavy run cycles, operators gain safer operation, fewer heat-related failures, and predictable uptime even when equipment runs hot and nonstop.

Stable Power for Long Industrial Run Cycles

By reducing the wear caused by ripple currents and constant electrical stress, LDF maintains consistent performance across variable loads and long-duration duty cycles.

  • In long-duration industrial operations, high ripple currents and continuous voltage stress wear down traditional capacitors, causing dielectric fatigue, unstable performance, and unpredictable behavior under variable loads.
  • LDF’s nanolayer structure dramatically reduces dielectric wear from ripple currents and constant electrical stress, delivering the high stability that power-conversion systems need during extended run times and fluctuating conditions.
  • With greater long-run stability, operators get predictable, reliable performance in applications like power-factor correction and utility systems, resulting in fewer failures, smoother operation, and higher uptime.

High-Heat Stability for Continuous Industrial Operation

LDF’s 50% lower self-heating and 135°C stability prevent thermal runaway, keeping systems reliable even in enclosed, high-temperature, long-duration environments.

  • Long-duration industrial equipment often runs in hot, enclosed, or poorly ventilated environments where traditional capacitors face thermal runaway risk, internal overheating, and early failure during continuous operation.
  • LDF’s nanolayer design cuts internal self-heating by 50% and maintains full performance up to 135°C, reducing thermal stress, preventing swelling, lowering cooling demands, and delivering stable operation even in harsh industrial temperatures.
  • With lower internal heat and more thermal headroom, operators gain cooler-running systems, fewer heat-related failures, safer performance during overloads, and longer equipment life in demanding, high-heat environments.

Up to 5x Longer Life in the Harshest Duty Cycles

With up to 5x longer life, LDF reduces the wear that causes early capacitor failures, delivering more uptime, fewer service calls, and lower maintenance costs.

  • In long-duration industrial operations, traditional capacitors break down early from high ripple currents, continuous voltage stress, and long run times without cool-down windows, leading to frequent failures, costly maintenance, and repeated shutdowns.
  • LDF’s nanolayer structure dramatically reduces dielectric wear and withstands the electrical and thermal stress that destroys conventional capacitors, delivering up to 5x longer life and significantly reducing replacement and maintenance cycles.
  • With longer-lasting capacitors, operators gain more equipment uptime, fewer service interruptions, and a lower total cost of ownership—resulting in higher productivity and longer system life across their industrial operations.

LDF vs. BOPP in Heavy-Duty Industrial Duty Cycles

Category Traditional BOPP Film Capacitors NanoPlex™ LDF Film Capacitors
High-Heat Capability Derates sharply above 85°C; limited high-heat tolerance Maintains full performance to 135°C with no derating
Long-Duration Operation Performance drifts during long operation; sensitive to heat buildup Designed for continuous run times with no cool-down required
Thermal Stability Higher internal heating; greater risk of thermal runaway 50% lower dissipation factor → significantly less self-heating
Lifespan in Heavy Duty Cycles Aging accelerates under ripple currents; frequent early failures Up to 5x longer life under high ripple currents and continuous voltage stress
Ripple Current Handling High ripple currents accelerate dielectric wear and shorten life Nanolayer design resists dielectric fatigue from high ripple currents
Voltage Stress Tolerance Lower stress tolerance; prone to drift, swelling, or cracking Withstands higher electrical stress during long-duration operation
Stability Over Time Performance drifts over time under electrical and thermal stress High stability → predictable behavior over long durations and variable loads
Thermal Runaway Risk Higher risk in enclosed or poorly ventilated environments Low; reduced internal heat and high thermal headroom
Maintenance Frequency Frequent replacements; high maintenance burden Significantly fewer replacements needed; lower maintenance
Impact on Uptime Downtime increases due to premature BOPP failures More uptime; fewer shutdowns from capacitor failure
Total Cost of Ownership Higher—short life, more failures, more cooling, more labor Lower—longer life + fewer failures + less cooling demand
Ideal Applications Light- to medium-duty cycles with moderate temperature conditions Heavy-duty cycles, high heat, HVDC, DC link, PFC, drives, welders, industrial motors

5 Operator FAQs for Long-Duty-Cycle Industrial Capacitors

Yes. LDF Film is engineered for long-duration operation and maintains stable performance even under constant load, with to its nanolayer structure that resists drift, dielectric fatigue, and voltage stress during long run cycles.

Yes. LDF maintains full performance up to 135°C with no derating and produces 50% less internal heat, allowing it to operate reliably in hot, enclosed, or poorly ventilated industrial spaces where traditional films fail.

LDF lasts up to 5x longer than BOPP because its nanolayers distribute electrical load and prevent the dielectric wear caused by ripple currents and constant voltage stress, dramatically extending lifespan in heavy-duty cycles.

LDF significantly reduces maintenance because it runs cooler, wears more slowly, and stays stable under stress, meaning far fewer capacitor replacements and fewer service interruptions over the life of the equipment.

Yes. LDF’s higher heat tolerance, reduced self-heating, and long-run stability lead to fewer failures, more uptime, and more predictable performance, helping operators avoid costly shutdowns and production losses.

Ready to Evaluate NanoPlex Films?

Request a sample kit of NanoPlex for in-house qualification, compatibility testing, and grid-level performance validation.